Mahogany Candy Dispenser

My dad absolutely LOVES peanut M&Ms, so I couldn’t think of anything better to give him than a sophisticated dispenser for his favorite candy. While looking for a gift to accomplish this, I saw Pneumatic Addict’s M&M Dispenser. My project is largely based on her’s (check out her article here).

The Problem to Solve

A custom gift for my dad that was made by me and integrated one of his favorite things.

Tools

  • Drill

  • Table Saw

  • Miter Saw

  • Palm Router

  • Jigsaw

  • Rotary Tool

  • Chisel

  • Screwdriver

  • Combination Square

  • Clamps

Materials

  • Mahogany (or other dark hardwood)

  • 1/4” Brass Rod

  • Brass Piano Hinge

  • Brass Finish Screws

  • Acrylic Sheet

  • Butcher Block Conditioner

  • Wood Glue

  • Peanut M&Ms (or similar sized candy)

Steps for Build

  1. Cut Material Down to Size

  2. Remove Candy Circle

  3. Cut Wood Grain Matched Face Out

  4. Clean up Cuts

  5. Glue Up Body

  6. Cut Head and Foot

  7. Route Chamfers

  8. Glue Foot and Sand

  9. Cut Acrylic Sheet to Size

  10. Apply Finish

  11. Cut Center & Hinge

  12. Install Polycrylic Sheet


1 - Cut Material Down to Size

Personally, I like to cut to length first. I have found that this lessens inconsistencies when ripping to final width.

CandyDispenser-InitialLayout
CandyDispenser-InitialRoughCutMiterSaw

Once cut down, I rip the roughest edge off of the stock . I do not currently have a jointer, so I run the smoothest side against my table saw fence at a minimum distance to the blade.

CandyDispenser-ThinRipCut

With one side ripped square, I flip the piece to rip the other side to its final width. This second rip cut should remove more material than the initial squaring rip cut.

CandyDispenser-FinalWidthCut

2 - Remove Candy Circle

Before drilling out the rotating candy dispenser, I used some relative measurements to mark the face for cuts. These marks included where the sides would be cut as well as the open footer and rotating component itself. By cutting the entire face from one piece of wood, the sides and center will have continuous grain.

CandyDispenser-MarkingLayout

Once marked, I used a hole saw to cut away the rotational component. The kerf of the hole saw is large enough to accommodate the necessary rotational gap. When using hole saws, I like to drill a pilot hole where the center is. Once done, I can start the cut on one side and finish from the other. This and some tape keep the faces very clean.

CandyDispenser-HoleSaw-CloseUp
CandyDispenser-HoleSaw

To create a slot for the candy to sit in, I used a forstner bit to remove the material. A drill press would be better for side cutting like this, but a drill works if you take your time.

CandyDispenser-CircleForstnerBit

3 - Cut Wood Grain Matched Face Out

To keep both side of the face parallel, I decided to make the initial cuts with my table saw. This requires cutting, disengaging the power just before final cut, and waiting for the blade to spin down before repeating on the other side. For stop cuts on the table saw, I always make sure to keep the piece perfectly still till the blade spins all the way down.

CandyDispenser-TableSawStopped

Once both sides have been cut, the jig saw is used to finish all major cuts.

CandyDispenser-Jigsaw1
CandyDispenser-Jigsaw2

4 - Clean Up Cuts

The hole saw left a small ridge on the circle and sides. I used a rotary tool with a sanding disk to quickly sand the ridge flush with the rest of the piece.

CandyDispenser-RotaryEdgeRemoval
CandyDispenser-RotaryCloseUp

The jigsaw and table saw blade kerfs were not exactly the same, so there is another small ridge on the corners. For these, I used a sharp chisel to even out the surfaces. A chisel is a great tool for evening out cuts and joints. I have a relatively cheap set, but use them all the time.

CandyDispenser-ChiselWork

Once the cuts had been cleaned up, it was time for a little hand sanding. I only hand sanded the parts that would be difficult to access once everything was glued up.

CandyDispenser-SandingSides

5 - Glue Up Body

Time to start assembly! I used Titebond II for this since it will not be outside or exposed to high temperatures. A glue brush is very helpful to in order to ensure the entire surface has had glue applied to it.

CandyDispenser-GlueBrush

I used pretty much all of my small to medium sized clamps to keep the pieces from moving. The edges will be flush and I certainly did not want anything to move around. Before the glue dried, I used a straw to clean out the squeeze out on the inside.

CandyDispenser-ClampUp

6 - Cut Head and Foot

Whenever possibly, I prefer relative measurements to numeric measurement & marking. When sizing the footer, I knew I wanted its overhang to be equal to the material thickness. Instead of measuring the thickness and marking that on both sides, I used a cutoff to directly mark the measurements.

CandyDispenser-RelativeMeasurement

Once marked, I could cut to the line with my miter and table saws.

CandyDispenser-FooterMiterSaw
CandyDispenser-FooterRipCut

The header was sized and cut the exact same way, but the relative measurements were marked flush with the body.

CandyDispenser-HeaderWide

7 - Route Chamfers

In order to ease the thick look of the header and footer, I decided to add a 45 degree chamfer to the edges. When I did this, I wore gloves which is extremely dangerous! I learned from the Instagram community that this is a very bad idea after-the-fact If you use a spinning tool like a router, don’t wear gloves.

CandyDispenser-Router1

When adding profiles on wood, I route the end grain first, then the face grain. The end grain has a tendency to blow out a little. If it blows out on the face, it will be cut away anyway.

CandyDispenser-Router2

The chamfer lightens the overall look of what could be a blocky project. Adds just a little flair to the project.


8 - Glue Foot and Sand

With the chamfers added, I could glue up the footer to the base. I made sure to apply glue to the base since it will all be touching the footer, but the whole footer will not be touching the base. When an exact centering is needed for positioning, a tool like a combination square cannot be beat. I also put a few clamps on it just to make sure nothing moved.

CandyDispenser-FooterGlueUp

9 - Cut Acrylic Sheet to Size

For the initial size of the clear, acrylic sheet, I laid the piece on the front and marked the overhang with a sharpie on the removable plastic. Once great thing about working with clear material is the ability to mark while on top of other pieces.

CandyDispenser-PolyInitialLayout
CandyDispenser-PolyCrossCut

Once cut to size, I used the same method to mark the opening for the candy to come through at the bottom. As with the footer, relative measurements are much better than measure and mark in this instance. The clear acrylic allowed me to simply mark with a sharpie and connect the dots with a straight edge.

CandyDispenser-FooterRelativemeasure

To cut the bottom opening out, I first attempted to use the “score and snap” method. However, for angled pieces, this did not work at all. Instead, I went back to my rotary tool with a cut off wheel. The cutoff wheel made quick work of the opening and was more accurate as well. Just don’t be too aggressive with the cuts. The thin cutoff wheels have a tendency to snap.

CandyDispenser-RotaryToolPoly

Since the screws that attach the acrylic to the base will show, I marked even spacing for them and drilled the final holes before continuing.


10 - Apply Finish

Because this is designed to be a peanut M&M dispenser, the finish must be food safe. I have heard a few debates about what finishes are food safe once cured. In this instance, I played it safe by using natural butcher block conditioner. The oil in the conditioner will make the wood grain pop while the wax will provide an added payer of protection.

CandyDispenser-Finish1
CandyDispenser-Finish2
CandyDispenser-Finish3
CandyDispenser-Finish4

11 - Cut Brass Rod & Hinge

For the brass, I again used relative measurements. I wanted the brass to be roughly aligned with the front of the footer, so used the thickness of the header to mark the depth.

CandyDispenser-BrassMarking

The brass rod was cut with an angle grinder as was the brass hinge. Both could be cut with a hacksaw, but the angle grinder is significantly faster. Either method will require minor cleanup with some files.

CandyDispenser-HingeGrinding
CandyDispenser-HingeFile

The brass rod needs some polishing that would normally come from a lathe. I do not have a lathe, so chucking the piece up in my drill will have to do. Once in the drill, I started with a file to add a chamfer and rough out the piece. Next, I moved through sandpaper grits starting with 250 all the way up to 2,000. The higher grits wipe away sand marks from lower grits and add a nice polish to the metal.

CandyDispenser-BrassRodFile
CandyDispenser-BrassRodDiff

12 - Add Center and Hinge

The brass rod will go in the center circle. Epoxy was used to make the bond permanent. Ideally, the surface of the brass would not be polished, but for this application, I think the bond will hold perfectly. I made sure to measure the indent in the body to mark the back indention before inserting with epoxy.

CandyDispenser-EpoxyCenter

The top was spaced slightly off the base by using the thickness of playing cards. This is my go-to method for spacing in most scenarios. With the top placed and spaced, I could add the hinge and mark locations for pilot holes.

CandyDispenser-HingeSpacing

If I were to do this again, I would use CA glue to fix the hinge in place before marking any pilot holes. Fortunately, it worked out and the holes were in the correct spot. Once they were drilled, I could hand screw them in place.

CandyDispenser-HingeScew

13 - Install Acrylic Sheet

The acrylic sheet was the final component for this build. Since the screws are all brass, I used a hand screw to install it. A power tool would strip the screw head immediately. With the screws installed, this project is complete and ready to be wrapped!

CandyDispenser-PolyScrew1
CandyDispenser-PolyScrew2

CandyDispenser-FinalShots1
CandyDispenser-FinalShots2

I am extremely happy with how this M&M Dispenser turned out. More importantly, my Dad loves it! This project was a great exercise in taking an existing project and adding your own twist to it. Huge thanks again to Elisha from Pneumatic Addict for letting me post my version of her awesome project. If you’re not following along with her work, you definitely should be (check out her Instagram here).

CandyDispenser-FinalShots3
CandyDispenser-FinalShots4

This project was also a great learning experience for working with brass and acrylic. I love working with new-to-me materials and these were two very versatile ones to work with.

CandyDispenser-FinalShots5
CandyDispenser-FinalShots6

I would love to hear what you think about this project. Let me know in the comments on the video or over on Instagram.